Issue
|
Page # |
Article Title |
Correction |
February 2012 |
27 |
Sanding Your Turned Work
|
The information in the
Sandpaper Comparison Chart
appeared incorrectly.
Click here for a revised version. |
February 2010 |
31 |
Weekend Tambour Gift Box
|
The third sentence in the paragraph under the heading "The Top, Bottom and Top Plate" heading reads as follows:
"Using a 1/4" straight bit in your router, form a 1/4"-deep dado on the bottom piece, ...".
It should read:
"Using a 1/4" straight bit in your router, form a 1/2"-deep dado on the bottom piece, ..." |
February 2010 |
45 |
Table and Seats for a Tight Space
|
The numbering between the Material List and the Bench Exploded view was incorrect.
Click here for a revised
Bench Material List & Exploded View. |
December 2009 |
41 |
Horizontal Tilt-top Router Table
|
There was an error in the drawing showing the hole location for the threaded insert.
Download the attached PDF for an explanation of the corrections. |
April 2009 |
19 |
Four Basic Rabbet Joints
|
References to our
Delta Unisaw Test Run video
were omitted from the article. |
April 2009 |
34 |
Classic Drop-leaf Table |
The inside dimension between the legs in the
"Table (End Views)" elevation drawing is incorrect.
It states 18-1/4" and should be 16-1/4" |
December 2008 |
49 |
Southwestern Entry Bench
|
There was an incorrect measurement
in the Exploded View drawing
of the Short Rails.
Download the attached PDF for a revised
Exploded View and Drawings.
|
December 2008 |
55 |
Modular Shelf System
|
There was an incorrect measurement
in the Exploded View drawing
of the Shelf Cleat Molding.
Download the attached PDF for a revised
Exploded
View and Drawings.
|
October 2008 |
61 |
Rolling Shop Table
|
The dimensions of the Caster Braces (#6)
of the Material List are incorrect.
Download the attached PDF for a revised
Exploded
View and Material List.
|
June 2008 |
43 |
Upper Kitchen Cabinets
|
The numbering in the Upper Cabinet Material List was incorrect, and there was an incorrect measurement on the Upper Cabinet (Section View) drawing.
Download the attached PDF for a revised
Exploded
View and Material List.
|
April 2007 |
53 |
Bathroom Vanity
|
Coutertop measurement is incorrect in Material List
Download & print the
Revised Bathroom Vanity Material List
|
February 2007 |
60 |
Road Maps of Woodworking
|
The fourth angle view of one of Ian's drawings had a detail omitted.
View the Revised Illustration
|
December 2006 |
20 |
T-nut Shelf-Pin Jig
(Tricks of the Trade) |
The third sentence states:
"I insert 5/16" T-nuts into holes…"
It should read:
"I insert 1/4" T-nuts into holes…" |
October 2006 |
39 |
Shop-built
Passage Door |
Material List incorrectly lists using 6/4 poplar.
It should say "8/4 poplar" |
August 2006 |
41 |
Drill Press Jig
with Pivoting and
Locking Fence
|
6th sentence in first paragraph states:
"Using this hole as a pivot point, draw a 23" radius curve on the right edge…"
It should read:
"Using this hole as a pivot point,
draw a 23-1/4" radius curve
on the right edge…" |
August 2006 |
53 |
Memorial Flag Case |
In the "Adjusting dimensions for flag sizes" sidebar,
the illustration's caption states:
"The inside measurements are X and 2x
(e.g. if X=10-14", then 2X=21-1/2")"
It should read:
"The inside measurements are X and 2x
(e.g. if X=10-14", then 2X=20-1/2")" |
August 2005 |
44 |
Pencil Post Bed
|
The length of the posts was printed incorrectly in the Material List.
The length listed is 62"
The correct length is 80" |